A State-Variable Filter is an active filter that uses multiple feedback techniques to produce filter responses (LowPass, BandPass and HighPass) from a single filter with user selection. Classical SVF filters include controls for Filter Frequency, Filter Q and Gain. With the ASVF-212, we included deep LFO control for the device’s parameters. A variety of textures and horizons of modulation morphing can be created by routing destinations such as Filter Freq, Filter Q, Low-High Filter Response, and Notch-Peak FIlter Response. The ASVF-212 has an additional Notch Filter (Band Stop filter) and Peak Filter (BandPass filter).  
The device can also take advantage of Envelope Follower tricks with modulation destinations for FIlter Freq, Filter Q, Low-High Filter Response, and Notch-Peak Filter Response with a few Envelope Follower detection modes.  
What makes the ASVF-212 different from a typical SVF filter? It is a Stereo filter-bank (LP, HP, BP, Notch, Peak filters) with deep LFO and Env. Follower modulation. The ASVF-212 includes a Blend knob (Dry/Wet mixture of incoming and processed signals) to create more interesting and creative effects. The user can use the included hard clipped Limiter to control the final signal by adjusting the necessary Gain and Pre-Gain (unprocessed) levels.

The ASVF-212 is a modern stereo SVF filter with advanced features and classical analog SVF possibilities. It allows for a lot of variations of active filtering, resulting in a unique sound.

Product details

Filter Frequency – Cuftoff Frequency of HighPass, BandPass and LowPass filters  
Filter Q – Strength of resonant peak at cutoff frequency  
Low-High Freq Response – Fade between LowPass and HighPass response  
Notch-Peak Freq Response – Fade between Notch/BandStop and Peak/BandPass response 

Notch Filter (Band Stop) 
A notch filter is basically the opposite of a BandPass filter, it rejects, or stops, a specific band of frequencies. A Notch filter is also known as a “Band Stop Filter”. It works as summing of HighPass and LowPass output responses. 

Peak Filter (Band Pass)

A Peak filter is a frequency filter that passes a narrow band of frequencies and stops all other frequencies. This is a very narrow BandPass filter and the opposite of a Notch filter. For example, peak filters are used in WahWah effects. 


Wave – LFO Waveforms: Sqr, Sine, Tri, Saw, Uniform, FlatMid, EarlyComb, Essence  
Destination – LFO destination: Filter Freq, Filter Q, Low/High Filter Response, Notch/Peak Filter Response  
Modulation Way – Increase / Reduce the destination mod parameter  
Mod Index – Ramping LFO steps. 0% switches from one value to the next  
Rate – LFO Rate (mode in sync with Step grid or Time in seconds)  
Random Amt – Scale each step of LFO by a random amount  
Sync Mode – Set the LFO rate in steps per beat or steps per second  
LFO Amt – Amount of the LFO modulation  
Retrigger – Restart LFO steps after pauses (sync = Sec), and when Bar beat changed (sync = Beats)  
Rate Affect – How much the value affects the LFO Rate (if Env.Follower is enabled – how it affects the LFO Rate)  
Drift Contour – How much the value affects the LFO Wave (if Env.Follower is enabled – how it affects the LFO Wave). Change the waveform from hard to soft curve. 

Envelope Follower

Mode – Envelope detection modes:  
LIN: Linear voltage measurement up to the threshold level;  
LOG: Logarithmic dB measurement above the threshold level;  
GATE: Switch off and on as the signal level passes the threshold  
LIN: Audio level for full modulation;  
LOG: Audio level for no modulation;  
GATE: switching Threshold.  
Attack – Rise time when the audio level increases, or the gate opens  
Release – Fall time when the audio level decreases, or the gate closes  
Destination – Off, Filter Frequency, Filter Q, Low/High and Notch/Peak frequency response 


Clip Limiter – Limiter on/off. CPU safety hard clipping limiter  
Release – Recovery time  
Pre-Gain – Gain of incoming signal  
Gain – Output Level Gain 


Bypass / On / Off – Standard fader with 3 modes: Bypass effect, On Effect, Off Effect  
Patch Browser – Open, Browse and Save your own patches  
Blend – Blend Dry/Wet functional of incoming and processed signals  
Soft Bypass – Bypass with fades of Vocoder effect activity (without glitches)